As an Amazon Associate I earn from qualifying purchases.
Yes: 1/2 in sheathing plywood is made and stamped at 15/32 in — 0.469 in or 11.9 mm, 1/32 in under a true half inch. 3/4 in is 23/32 in (0.719 in, 18.3 mm), 5/8 in is 19/32 in (0.594 in) and 3/8 in is 11/32 in (0.344 in); OSB is sold at its real 7/16 in.
Plywood and OSB are sold by a rounded trade size, but each panel is made to an actual thickness in 32nds of an inch, and that is what the grade stamp prints. Sheathing sold as 1/2 inch is 15/32 inch — 0.469 inch or 11.9 mm, 1/32 inch thinner than its name — and carries the 32/16 roof span rating. 5/8 inch plywood is 19/32 (0.594 inch, 15.1 mm, 40/20), 3/4 inch is 23/32 (0.719 inch, 18.3 mm, 48/24) and 3/8 inch is usually 11/32 (0.344 inch, 8.7 mm, 24/0). OSB is the exception: it is sold at its real 7/16 inch (0.4375 inch, 11.1 mm, 24/16), which is not the same panel as 1/2 inch plywood. Imported and Baltic birch plywood is made in millimetres instead, so 18 mm (0.709 inch) stands in for 3/4. For strength the 1/32 inch does not matter, because codes rate the stamped panel; for stacking, joinery and hardware such as H-clips, buy and cut to the stamp. Enter a measured thickness to identify the panel.
Short answer: plywood is thinner than its shelf name. Sheathing sold as 1/2 in is 15/32 in (0.469 in, 11.9 mm), 5/8 in is 19/32 in (0.594 in, 15.1 mm) and 3/4 in is 23/32 in (0.719 in, 18.3 mm), each 1/32 in under the name; 3/8 in is usually 11/32 in (0.344 in, 8.7 mm). OSB is sold at its real 7/16 in (0.4375 in, 11.1 mm). Metric plywood is made in millimetres: 18 mm is 0.709 in.
| Sold as | Actual | Decimal | mm | Span rating | Typical use |
|---|---|---|---|---|---|
| 3/8 in plywood | 11/32 in | 0.344 in | 8.7 | 24/0 | Wall sheathing; roofs on 24 in centers only with H-clips |
| 7/16 in OSB | 7/16 in | 0.438 in | 11.1 | 24/16 | The usual roof and wall sheathing on 24 in trusses |
| 1/2 in plywood | 15/32 in | 0.469 in | 11.9 | 32/16 | Roof sheathing, wall sheathing, shed floors over 16 in joists |
| 5/8 in plywood | 19/32 in | 0.594 in | 15.1 | 40/20 | Stiffer roof decks, tile and slate roofs, subfloor on 19.2 in joists |
| 3/4 in plywood | 23/32 in | 0.719 in | 18.3 | 48/24 | Tongue-and-groove subfloor on 24 in joists, wide roof spans |
| Metric panel | Inches | Nearest 32nd | Shelved as |
|---|---|---|---|
| 6 mm | 0.236 in | 1/4 in | 1/4 in |
| 9 mm | 0.354 in | 11/32 in | 3/8 in |
| 12 mm | 0.472 in | 15/32 in | 1/2 in |
| 15 mm | 0.591 in | 19/32 in | 5/8 in |
| 18 mm | 0.709 in | 23/32 in | 3/4 in |
Yes. 15/32 in is what "1/2 inch" sheathing plywood is actually made and stamped at: 0.469 in, or 11.9 mm, which is 1/32 in (0.8 mm) thinner than a true half inch. It carries the 32/16 roof span rating, takes the same 1/2 in H-clips and 8d nails, and is what the shelf tag means by 1/2 in.
Structural 3/4 in plywood — tongue-and-groove subfloor and sheathing — is 23/32 in: 0.719 in or 18.3 mm. Imported cabinet and Baltic birch panels sold as 3/4 in are usually 18 mm, which is 0.709 in, a hair thinner again. Measure before you cut dadoes or buy edge banding.
15 ÷ 32 = 0.46875 in, usually rounded to 0.469 in. In millimetres that is 0.46875 × 25.4 = 11.9 mm.
Yes. Sheathing sold as 3/8 in is usually stamped 11/32 in: 0.344 in or 8.7 mm, 1/32 in under 3/8 (0.375 in). On a roof it is a 24/0 panel: it spans 24 in centers only with H-clips or blocking at the edges, and 20 in without.
No. 7/16 in is 0.4375 in (11.1 mm), 1/32 in thinner than 15/32 in plywood. It is stamped 24/16, so it spans 24 in truss centers with or without clips, while 15/32 plywood is 32/16. On ordinary 24 in trusses either panel meets the code minimum.
The listed size is a trade name rounded to the familiar fraction; the panel itself is made to an actual thickness in 32nds of an inch, which is what the grade stamp prints (the "Performance Category" on US sheathing). The US product standards for plywood (PS 1) and structural panels (PS 2) allow about ±1/32 in on unsanded panels this thin, so a 15/32 sheet can measure anywhere from about 7/16 to 1/2 in.
On 24 in trusses the code minimum is 7/16 in OSB (24/16) or 15/32 in plywood (32/16) without clips, or 3/8 in (24/0) with H-clips. At 16 in rafters 3/8 in spans without clips. Heavier roofs such as tile, and high snow loads, call for 19/32 or 23/32 in.
Most subfloors are 23/32 in (sold as 3/4 in) tongue-and-groove panels rated 24 oc, which cover joists up to 24 in apart; 19/32 in (5/8 in) panels rated 20 oc cover joists up to 19.2 in. Glue and screw them to the joists so the floor does not squeak.
Buying the panels? The roof sheathing calculator counts sheets, nails and waste for your roof.
Need the whole roof at once? The free roofing calculator works out roof area, squares, shingle bundles, underlayment, drip edge, ridge cap and installed cost from one set of measurements.