13/12 Roof Pitch

47.3 Degrees, 108.3% Slope and a 1.4743 Area Multiplier

What is a 13/12 roof pitch in degrees?

A 13/12 roof pitch is 47.3 degrees. It rises 13 inches for every 12 inches of horizontal run, which is a 108.3% slope and an area multiplier of 1.4743 — so a 2,000 square foot footprint at 13/12 is 2,949 square feet of roof.

A 13/12 roof pitch rises 13 inches for every 12 inches of horizontal run. That works out at 47.3 degrees, a slope of 108.3%, and an area multiplier of 1.4743 — so a flat footprint multiplied by 1.4743 gives the actual sloped roof surface you have to buy material for. Everything below is derived from that single ratio: the roof area at common house sizes, how many bundles of shingles it takes, whether the roof is walkable, and which coverings the code allows at this slope.

What 13/12 means in every unit

13/12 roof pitch converted
Unit	Value	What it is
Pitch	13/12	Rises 13 inches over 12 inches of run
Angle	47.3°	What a digital level or inclinometer reads
Slope	108.3%	Rise divided by run — used in drainage work
Area multiplier	1.4743	Multiply the footprint by this for the real roof area
Rafter length per foot of run	1.474 ft	Feet of rafter per foot of horizontal run

All four describe the same slope. Pitch is what a lumber yard, a truss plant and a code table use; degrees is what an instrument reads; the multiplier is the one you order material against.

Roof area and material at 13/12

Roof area, squares and bundles at 13/12 pitch
Footprint	Roof area at 13/12	Squares	Bundles at 10% waste	Bundles at 15% waste
1,000 sq ft	1,474 sq ft	14.7	49	51
1,500 sq ft	2,211 sq ft	22.1	74	77
2,000 sq ft	2,949 sq ft	29.5	98	102
2,500 sq ft	3,686 sq ft	36.9	122	128
3,000 sq ft	4,423 sq ft	44.2	147	153

A 13/12 roof adds 47.4% to the footprint area. On a 2,000 square foot footprint that is 949 extra square feet of covering — 9.5 squares you would not have ordered from the ground measurement alone.

Working on a 13/12 roof

Staging and fall protection. Specialist work.

Standard asphalt shingle installation, with no low-slope underlayment requirement.

Waste factor: the usual allowance still applies — 10% for a simple gable, 15% for a hip roof, up to 20% for a cut-up roof. Pitch changes the area, not the waste rule.
Labour: work above 9/12 takes roughly twice as long per square as work at 4/12, because material has to be carried rather than slid and everything needs staging.
Ventilation: unaffected by pitch. The 1/300 rule is set by attic floor area, not by slope.
Rafter length: multiply the horizontal run by 1.5 to get the rafter, before adding the overhang.

How to confirm your roof is 13/12

Hold a 12-inch level against a rafter in the attic, bring it level, and measure straight down from the 12-inch mark. If the drop is 13 inches, the roof is 13/12.
A digital inclinometer on a rafter should read 47.3 degrees, within a few tenths.
A speed square with a pitch scale, held against a level, reads the ratio directly.
Round to the nearest standard pitch. Rafters and trusses are cut to whole increments, so ordering against an unrounded decimal produces a roof that does not meet at the ridge.

Frequently asked questions

What is 13/12 pitch in degrees?

A 13/12 roof pitch is 47.3 degrees. Take the arctangent of 13 divided by 12. The same slope is 108.3% and has an area multiplier of 1.4743.

What is the 13/12 roof pitch multiplier?

1.4743. Multiply the building footprint by 1.4743 to get the actual sloped roof area — a 2,000 square foot footprint at 13/12 is 2,949 square feet of roof.

Can you put shingles on a 13/12 roof?

Yes. 13/12 is above the 4/12 threshold, so standard shingle installation applies with no low-slope underlayment requirement.

Can you walk on a 13/12 roof?

Not casually. At 13/12 you need roof jacks or staging and proper fall protection — the angle is 47.3 degrees.